Forum Post: bq77PL900 EVSW Source Code
Is the source code for bq77PL900 EVSW (http://www.ti.com/product/bq77pl900) available?
View ArticleForum Post: source code for bq2416xEVM software?
Is the source code for bq2416xEVM software http://www.ti.com/tool/bq24160evm-721?DCMP=hpa_pmp_mr&HQS=bq24160EVM-pr) available?
View ArticleForum Post: Vin 2.7-9 volts, Vout 5 volts, Iout - 10mA, which solution will...
Hello.For certain product, we need 5 volts at 10mA current. The input voltage may change from 2.7 to 9 volts. Initially, TPS63060 seemed to be a good choice, but this is rather powerfull IC, and...
View ArticleForum Post: UCC28600 EMI
Hi,I have designed a 10Watt SMPS using UCC28600. My design is having lot of EMI issues and failing in radiated emission 30-100Mhz band. I used a 1K resistor in gate path for slow turn on of the mosfet...
View ArticleForum Post: RE: EV2400 and bqEVSW------
Shirish,Thanks a lot for your assistance.That is what I did in the first place, - downloaded the EV2400 Support Components_ 20110524.exe but when I should run the EVSW (09.99) after running this sw i...
View ArticleForum Post: RE: bq20z75 V1.81 - Control of DSG in Battery Status during UN...
Dear all, I might have made my question to complicated - to make it more simple....If during UN Thermal testing the SOT Chg temperature is exceeded with more than 10 deg C but no chg current is flowing...
View ArticleForum Post: RE: LM3480 / Over current protection and over temperature protection
Hi Jones-san,Thank you for your response. I confirmed the figure 20 and 21, and understood that LM3480 has only thermal protection only, right?Best Regards,Sonoki
View ArticleForum Post: RE: LM5575 Prototype Problems
It looks like I'll have everything I need for thorough testing on Wednesday, but in the meantime I've reviewed the data sheet and have a couple of questions.On page 12, the equation for Rramp is...
View ArticleForum Post: RE: Maximum Charging current of BQ24650 .
Hi,i have some questions and need your helping.First,the working current of bq24650 EVM circuit is about 10mA ,when I use IRL7833 to replace SI7288 ,is up to 40mA,that is why? IRL7833 feature...
View ArticleForum Post: LM5006 output capacitor
I see on the LM5006 eval board, Vout is set to 5V, and the output capacitor (C2) is 15uF, 16V, X7R. I have used this exact part in my design and it is working well. However, I am hoping to replace...
View ArticleForum Post: TPS7A3301 TPS7A4700 protection diodes
Hi SupportDo the above parts require protection diodes around them as per 78xx 79xx LM317/337 series? i.e. Vin to Vout reverse, Vout to Gnd for dual rail supply?ThanksJD
View ArticleForum Post: RE: USB to GPIO GUI - PMBus Group Command
Thank you for your rapid responses! This has been helpful.
View ArticleForum Post: RE: LM2594HMV-AD - Different National and TI Data Sheets
-Adding National Datasheet for Dan
View ArticleForum Post: TPS2490 and LM5069 Over Voltage Protection
Looking for a similar product like the LT4356 from Linear. Need a high side FET controller that clamps the output voltage when there is an OVP and does not shutoff like the LM5060.I found similar parts...
View ArticleForum Post: Generation of system reset pulse with UCD90120A from the Fusion GUI
I want to create the inverse of the system reset pulse shown in Figure 20 of the UCD90120A data sheet from the Fusion GUI. I want the SYSTEM RESET to be initially high and them pulse low for 1mS after...
View ArticleForum Post: RE: LM350K-STEEL unstable
A preliminary check shows that there have been zero changes to LM350K-STEEL at the silicon level. Queries have been sent out, but due to time zone differences it will be several hours, at least, before...
View ArticleForum Post: RE: BQ24250 Evaluation module
I have test setup that is mentioned in the section 5 of user guide of BQ2425xevm-150 with the battery emulator (figure 3) without the TBH25P5R6 resistors. In section 5.5.1 when I measure A2 it is...
View ArticleForum Post: RE: BQ34Z100 - Capacity goes to zero with no load after a day or two
Hi Tom, Thank you for the input.We haven't tried it yet, we wanted to do some more testing on more systems first. When we detect the change from 100% down to 0% we send a reset and re-enable IT to...
View Article