Forum Post: LM5017 burns out on start up.
Hello!,Can somebody tell me what I'm doing wrong whit my prototype circuit??, LM5017 gets burned as soon the UVLO voltage is reached (Around 67V). I burned my 5 samples trying to make it work. I tried...
View ArticleForum Post: RE: bq24163 cannot detect usb charger
when disconnect to TPS65951, BQ24163 can detect the usb charger.
View ArticleForum Post: RE: BQ77910A recovery from OC (Over Current) and SCD (Short...
Dear WM5295,thanks for your answers,how can I check if it is a protection or reset, since I can't use polling? if it is DPCKN rising to slow, how can I make sure it will go faster for the currnet I'm...
View ArticleForum Post: How to disable the Watchdog timer function of the...
Hi, SirHow to disable the watchdog timer function of the TPS3824-33DBVT(TPS3823-33DBVT) ?Is it maybe the enable function pin of the /MR Pin of the TPS3824-33DBVT?Many thanks and wish everyone all the...
View ArticleForum Post: TI 3 phases PFC reference design
Hello All, Does TI has PFC pre-regulator 3 phases reference design for Air condition?Input: AC 3 phaseoutput power: 10KW NT
View ArticleForum Post: PCB coil
HiI am using bq51013B and wanted to implement its coil antenna on the PCB itself.My question is do you have any kind or recommendations for such design?if not, the main issue I need to pay attention to...
View ArticleForum Post: RE: LM5017 burns out on start up.
I had some unknown problems with UCC3895 and finally I concluded it was the chip problem. I think shorter time to market, make newer chips have some problems specially in preliminary versions.
View ArticleForum Post: RE: HTSSOP28 / PWP package Step model link broken
The link is still broken or the STEP file is missing
View ArticleForum Post: bq27500-v130 with small capacity Li-Ion single-cell batteries?
Hi there,I haven't used a fuel gauge IC before and I was hoping someone could just check that I am not misleading myself - I plan to purchase the EVM to de-risk. I am looking at the bq27500-v130 to...
View ArticleForum Post: TLC5916 LED driver for TFT assistance
I'm going to be doing a project using the TLC5916 LED driver which will control a TFT LCD. However, I could use some assistance as to how to properly configure and setup the driver. The display I am...
View ArticleForum Post: RE: lcd
Dear SirThanks for your reply. Is it is possible to Connect clock data in series.Regards,Tanvi
View ArticleForum Post: RE: connection problem with bq500211A and BQ51050B. Maybe...
The schematic you have used is from bq500211A data sheet figure 8. “The designed receiver works fine with the purchased bq500211AEVM. But if I put the receiver on the self designed Transmitter board...
View ArticleForum Post: RE: RE:TPS2384EVM 64-bit drivers available for download
Thanks Leonard,We will see what we can do to get a WIN 32 machine to run this with. I appreciate the quick response. Go ahead and mark as complete.Frank
View ArticleForum Post: **INFO**Error in bq500211A Data Sheet Figure 8, Low-Cost Application
In the bq500211A Data Sheet (Dec 2012) Figure 8, “bq500211A Typical Low-Cost Application Diagram” pin 46 is shown grounded. Pin 46 is V_Sense which will sample the input voltage, when input voltage is...
View ArticleForum Post: TPS61054/TPS61055 for continuous LED use
Hello,I'm developing a circuit to power a 240lm LED from two AA batteries continuously, and I'm looking for an LED driver for the high brightness LED. I found the TPS61054 which looks like it may work,...
View ArticleForum Post: DCV01 common mode slew rate
Does anybody have any information about the common mode or isolated slew rate that the DCV01 range (or similar parts) can endure without any reliability or interruption of service problems?For example...
View ArticleForum Post: RE: LM5122 and TINA-TI
... unfortunately my PSpice tool, Altium Designer 2013 didn't understand this format, as the support told me. So this model is just useless.I think, it will be a good idea to make a TINA-TI compatible...
View ArticleForum Post: RE: BqGaugeStudio and BqCONFIG not worked with EV2300??
Hi Bryan,The guage studio is a product of the handheld team. I will see if someone can address your problem. thanksOnyx
View ArticleForum Post: RE: How to disable the Watchdog timer function of the...
Hi, DavidMany thanks for your reply.I got it.Many thanks and wish you all the best!!Andy
View ArticleForum Post: RE: TPS65070 input overvoltage protection cicuit
The absolute voltage ratings are listed in the Absolute Voltage Rating Table on page 2 of the datasheet. If you violate these rated voltages you are at risk of damaging the part.The recommended...
View Article